# Split a model for 3D printing in Blender

> Split a model that is too big for your print bed in Blender: Bisect with Fill, Boolean cuts, closed cut faces, pin sockets and one STL per part, all tested.

- Page: https://mendboxstudio.com/guides/split-model-for-3d-printing
- Updated: 2026-11-16
- Publisher: Mendbox Studio (Dynamic Flower Unipessoal LDA, Portugal)

To split a model for 3D printing in Blender, check its size in millimetres first, then cut it into parts with **Mesh > Bisect** (with **Fill** on) or with a Boolean modifier and a cutter cube, make sure every part is a closed solid, and export the parts as STL files. Add pin sockets if the parts have to line up when you glue them. I ran each step below on a test mesh in Blender 4.2, 4.5 and 5.2, and checked the result for open edges.

## Step 1: check the size against your bed

1. Open the **Scene Properties** tab, **Units** panel. Set **Unit System** to **Metric**, **Unit Scale** to `0.001` and **Length** to **Millimeters**. Now one Blender unit is one millimetre.
2. Select the model, press **N** and open the **Item** tab. **Dimensions** shows the size. These values include object scale.
3. Compare each side with your printer's build volume. Height is a limit too.

This also matters for export. With default settings the STL exporter writes the plain Blender-unit numbers and ignores the Unit Scale (its **Scene Unit** option is off). In my test a cube at 10 units went into the file as 10. Slicers read STL numbers as millimetres, so with this unit setup the file matches what you saw.

If the model needs resizing, scale it (**S**) and apply the scale (**Ctrl A > Scale**), so later cuts and exports use the real numbers.

## Step 2: cut with Bisect

Bisect cuts a mesh along one plane and can close the cut for you.

1. Select the model, press **Tab** for Edit Mode, and press **A** to select everything.
2. Choose **Mesh > Bisect** (the toolbar has a Bisect tool too). Drag a line across the model in the viewport to place the plane.
3. Open the **Adjust Last Operation** panel in the bottom-left corner and type the **Plane Point** and **Plane Normal**, for example `0, 0, 120` and `0, 0, 1` for a flat cut at 120 mm height.
4. Switch on **Fill**. Switch on **Clear Inner** to delete the part on the side opposite the plane normal, or **Clear Outer** for the other side.

Fill matters. In my test a sphere cut without **Fill** had 32 open boundary edges, and with **Fill** it had none. Fill covers the cut with a single flat face, so the half is a closed solid.

To keep both halves, duplicate the object first (**Shift D**, then right-click to cancel the move). Cut one copy with **Clear Inner** and the other with **Clear Outer**, same plane. In my test the two halves added up to the volume of the original (4.1219 cubic units against 2.3700 plus 1.7519).

## Step 3: cut with a Boolean and a cutter cube

A Boolean suits cuts you want to move or repeat, because the cutter stays a normal object.

1. Add a cube (**Shift A > Mesh > Cube**) and scale it so one face lies exactly on the cut position and the cube covers everything on one side of it. This is your cutter.
2. Duplicate the model (**Shift D**). You will have two copies.
3. On the first copy open the **Modifiers** tab and choose **Add Modifier > Generate > Boolean**. Set **Operation** to **Difference**, **Operand Type** to **Object**, and pick the cutter. Set **Solver** to **Exact**.
4. Apply the modifier with **Ctrl A** while hovering over it.
5. On the second copy add the same modifier with **Operation** set to **Intersect** and apply it.

In 4.2 the other solver is called **Fast**; 4.5 adds **Manifold**, and in 5.x Fast is renamed **Float**. Fast/Float gave the same closed halves on a clean sphere in my test; Manifold was not tested. Start with **Exact**. Hide the cutter when both are applied.

Difference keeps what the cutter does not cover, Intersect keeps what it does. My two test halves again added up to the volume of the original, and both were closed.

> A Boolean needs the model itself to be closed. If it fails or leaves holes, find the problem with **Select > Select All by Trait > Non Manifold** (Edit Mode) and see [how to clean up an imported STL](https://mendboxstudio.com/guides/clean-up-imported-stl).

## Step 4: make the cut face solid

A Boolean closes the cut for you. If you cut with Bisect and left **Fill** off, or you deleted faces by hand, close it yourself:

1. In Edit Mode choose **Select > Select All by Trait > Non Manifold**. The open edge loop of the cut is selected (32 edges in my test).
2. Press **F** to fill it. The result is closed, with one large flat face.
3. For quads on the cut face, choose **Face > Grid Fill** instead. It worked on the same loop and gave a closed result too. **F** leaves one n-gon, which is fine for printing.

For holes that are not a flat loop, see [how to fill a hole with quads](https://mendboxstudio.com/guides/fill-hole-with-quads).

## Step 5: add pin sockets so the parts line up

Glued flat faces slide against each other. Round pins and sockets fix that.

1. Add a cylinder (**Shift A > Mesh > Cylinder**) for the socket: a radius a little bigger than the pin, and a length that reaches into both halves. Centre it on the cut plane.
2. Apply a Boolean **Difference** with the cylinder as operand to the lower half, and again to the upper half. The same cylinder cuts a socket in both.
3. Model a pin as a second cylinder, a bit smaller than the socket, as long as the two socket depths together. Print it separately.

In my test both halves got the socket and stayed closed. A printed pin needs clearance. For example, a 6 mm pin in a 6.4 mm socket leaves 0.2 mm each side (my test used radii of 0.30 and 0.32 units). Printers differ, so print one pair first. Keep sockets away from the outline, where they would leave a paper-thin wall.

## Step 6: separate loose parts

If a cut leaves several pieces in one object, split them into objects. In my test a Boolean Difference with a thin slab through a sphere left two floating halves in one mesh.

1. In Edit Mode press **A**, then **P** and choose **By Loose Parts**. The path is **Mesh > Separate > By Loose Parts**.
2. Back in Object Mode each piece is its own object. Both pieces were closed in my test.

## Cuts that are not flat

Bisect and a cutter cube make flat cuts. For a curved dividing line, select the faces on one side in Edit Mode and press **P > Selection** (**Mesh > Separate > Selection**). In my test I selected a wavy band of faces on a UV sphere (the dividing line followed z = 0.25 sin 3x) and separated it. That gave two objects of 256 faces each, both open along a 40-edge boundary. Pressing **F** on each boundary loop closed both parts with a single 40-sided face. The two cut faces are not flat, so they will not sit flush against each other, and you have to check the fit and the walls yourself. BedSplit below only cuts flat planes.

## Step 7: check every part

Check each part before you slice it. The built-in way:

1. In Edit Mode choose **Select > Select All by Trait > Non Manifold**. Nothing should be selected. Anything selected is an open edge or a bad vertex.
2. Turn on **Overlays > Statistics** to see face and vertex counts, and check the **Dimensions** of each part in the **Item** tab against the bed.

The 3D-Print Toolbox is the usual extra check. Since Blender 4.2 it is an extension, installed from **Edit > Preferences > Get Extensions**. I did not test it, so this guide uses the built-in selection.

## Step 8: export only the parts

1. Select the parts you want. In Blender 4.2 and later, choose **File > Export > STL (.stl)**.
2. On the right of the file window switch on **Export Selected Objects**. Leave **Scene Unit** off, as explained in step 1, and decide about **Apply Modifiers**. If you did not apply your Boolean modifiers, switch it on.

In my test, with **Export Selected Objects** on, only the selected cube was in the file, 12 triangles, and with it off both cubes were, 24 triangles.

## What goes wrong

- **The cut leaves a hole.** Fill was off, or the model was not closed. Use steps 4 and 7.
- **The two halves overlap or leave a gap.** The Bisect plane and the cutter face are not on the same plane. Type the plane numbers.
- **The model prints at the wrong size.** The unit setup in step 1 was skipped.
- **The part is still too big.** Cut again along another axis. Every cut means more fill, sockets and checks.
- More fixes are on the [BedSplit troubleshooting page](https://mendboxstudio.com/docs/bedsplit/troubleshooting).

## Which method fits

| Method | Good for | Breaks when |
|---|---|---|
| Bisect with Fill | One flat cut, fast | Many cuts, or sockets by hand |
| Boolean with a cutter cube | Cut shapes you control, repeatable | Mesh is not closed |
| Grid Fill or F on the cut | Fixing a cut left open | The cut is not a flat loop |
| Cylinder Boolean for pins | Alignment between parts | You need dozens of joints |
| Separate by Loose Parts | Splitting one object into objects | Parts touch each other |

## Faster with BedSplit

With many cuts, the manual route repeats the chain above for every joint. [BedSplit](https://mendboxstudio.com/addons/bedsplit) does it for you:

- Pick your printer in the **BedSplit** tab of the sidebar (**N**), or choose **Custom** and type the bed size. It has presets for Bambu Lab, Prusa, Creality, Anycubic, Elegoo, Sovol and Voron machines.
- Turn on **Resize for print** and enter the longest side in millimetres, so you do not set up units.
- Press **Find Cuts** to see the cut planes in the viewport, move or remove a plane, or add one with the X, Y or Z buttons, then press **Split to Bed**.
- Each joint gets round dowel sockets in both faces, and you set the diameter, depth, clearance and the dowels per joint. A socket is only placed where the wall is thick enough.
- Each part is turned flat on its cut face, the **Result** panel lists every part with its size and whether it fits and is closed, and **Export STL** writes one file per part in millimetres, plus the dowel.
- Holes, flipped normals and overlapping shells are repaired first. The parts are new objects and your original stays.

Its limits: the cuts are flat planes along X, Y and Z (you can move them, not rotate them), the dowels are round, and there is no hollowing or supports. It works in Blender 4.2 and newer. The steps are in the [BedSplit workflows](https://mendboxstudio.com/docs/bedsplit/workflows).

The free BedSplit Lite splits a watertight model to your bed with flat cuts and exports one STL per part, without dowels, mesh repair or the cut preview.

For one or two cuts, the manual methods above are enough.

---
Source: https://mendboxstudio.com/guides/split-model-for-3d-printing
