BedSplit workflows: model to printed parts
Fit a figure to a 220 mm bed
Say you have a 600 mm tall statue and an Ender 3 class printer.
- Select the statue in Object Mode. Press N and open the BedSplit tab.
- In Printer choose "Creality Ender 3 / V3 SE (220 × 220 × 250)". This is also the default.
- Under Model size turn on Resize for print and set Longest side, mm to 600. If the model is already modelled at real size, leave it off. The line "Now: ... mm longest side" shows what Blender currently thinks.
- Press Split to Bed.
- Look at the Result panel. Each part row shows its size and a check mark. The parts sit in a grid beside the model, each lying on a cut face.
Because the bed is 250 mm high, a 600 mm model needs three slabs along its tall axis. BedSplit uses the smallest number of slabs per axis that fits the bed.
Preview and choose the cuts
Automatic cuts are a starting point. To control where the model is cut:
- Press Find Cuts. Planes appear in the viewport and a row per plane appears in the Cuts box.
- Read the row: the letter is the axis and the number is millimetres from the start of the model along it.
- Edit the number to slide a plane. Typical reasons: keep a cut away from a face, a hand, a thin sword blade, or put a seam where it is easy to hide.
- Remove a plane with the X button, or press Add cut X, Y or Z to add one in the middle of the largest remaining piece, then move it.
- Press Split to Bed. It uses your list exactly.
Two things to remember. Your own cut list is not checked against the bed, so if you move a plane too far a part may end up larger than the bed and the result panel will say so. And if you move or scale the source object, or change the printer or size settings, the list is discarded and the panel shows Automatic again.
Tip: if a cut passes through a very thin section, the dowel may not fit there. Slide the plane a few millimetres to a thicker section and split again.
Add dowels
Dowels are on by default. The Dowels box sets them:
- Dowel diameter, mm: 6 is a good start. A larger dowel is stronger but needs thicker walls.
- Depth in each part, mm: 6 means the dowel is 12 mm long and goes 6 mm into each side.
- Clearance, mm: 0.2 suits most printers. If you printed the dowels and they do not enter the sockets, raise it in steps, for example to 0.3, and split again.
- Dowels per joint: 2 gives alignment against twisting. Use 1 to keep sockets away from thin areas, or 3 for large faces.
- Press Split to Bed again after any change. The settings are applied during the split, not live.
After the split read the Result panel for a line such as "N joint(s) without dowel (wall too thin): glue these". Those joints are plain flat faces.
Repair and check
You do not run a separate repair. Split to Bed repairs first and reports it in the Result panel:
- "Repaired: holes closed, normals fixed" or "Repaired: overlapping shells joined" are mild and keep the shape.
- "Repaired: surface rebuilt (within x mm)" means the mesh was rebuilt as a new surface, within x millimetres of the original.
- "Heavy repair ... fine detail smoothed" means the rebuild moved the surface more than 0.5 mm. Compare the parts to the original. If a feature you care about is lost, repair that area in Blender first and split again.
A clean closed mesh with no problems produces no repair message.
Export the STL files
- In the Result panel press Export STL.
- Choose a folder. It is created if it does not exist.
- You get one file per part (for example "Knight_part_01.stl") and one dowel file with the count in its name (for example "Knight_dowel_x6.stl"). Everything is in millimetres.
- In your slicer import the parts. Each part is already oriented with its cut face on the ground, so no extra rotation is usually needed.
If you slice at a different scale than the export, the parts will not match the sockets, so import at 100 percent.
Print and assemble
Tips that follow from the dowel settings:
- Print the dowel file as many times as the name says. The count is the number of dowels in the whole model.
- Do a test first: print one small joint pair and one dowel and try the fit. Printers differ.
- If a dowel is too tight, raise Clearance, mm and split again. If it is loose, lower it, though 0.2 mm is the setting the add-on was built around.
- Dowels are twice the depth in length, with sockets slightly deeper than the half length, so they bottom out with a small gap rather than jamming.
- Use glue on the flat faces, and a little in the sockets. The dowels align the parts, the glue holds them.
- Dry fit all parts before gluing. Joints with no dowels need to be aligned by eye.
- For joints the panel reported as lacking dowels, glue flat faces and clamp.
See troubleshooting when something goes wrong, and the guide on splitting a model for 3D printing for the manual method.
Related
- Product page: BedSplit
- Troubleshooting
- Guide: how to split a model for 3D printing